Mobile Home Repair Heating and Cooling


More Coleman Parts

Gas Furnace Parts
Electric Furnace Parts
Blend Air Parts
Chimneys & Ductwork
A/C Parts
Filters & Misc

Other

Generic Parts
Furnace Manuals
Coleman Parts
Duo-Therm Parts
Goodman Parts
Nordyne Parts
Electrical Parts
NOS Parts
Ordering Policies
Mobile Home Parts

Catalog Categories

Books & Videos
Miscellaneous
Hardware
Electrical
Exhaust Fans
Belly Repairs
Skylights
Repair Tape
Plumbing
Pex
Heating & Cooling
Solar



COLEMAN CHIMNEYS & DUCTWORK


Page down or Click Here to visit our new easy-to-search website for ordering parts.

To place an order, call us at 605-229-2627 (9-5 M-F).
Or order online anytime. Same day shipping on most parts.
Search for your part.
Need help finding the right part, please e-mail us or call 605-229-2627.
Our Cheat Sheet may list parts for your a/c or heat pump.

TIP: To find a part on this page, type 'Control F' and enter the part number or name.

4000-7101C Standard Roof Jack 10"-19"

Adjustable from 10"-19" when measured from roof (not ceiling) to top of furnace. This 4000 series roof jack is used on almost all Coleman gas furnaces including CGAT, COAS, COAT, DGAA, DGAH, DGAM, DGAT, DGPA, DGPH, DGPT, DLAS, 7900 and 7600 models. For older furnaces, check your data plate or e-mail us. Swivel flashing allows installation on roof pitches ranging from 0/12 to 5/12. Installation instructions included. Outside pipe is 8-1/4" which fits over about an 8" pipe on the furnace. Inside pipe is 5-1/4" which fits over about a 5" pipe on the furnace. Your price $171.00.
View instruction sheet.
4000-7101C standard Coleman roof jack. 4000-4241 Hydroment Sealant

Apply to underside of roof jack flashing during installation and at swivel joint. Your price $14.95.

Hydroment seal
4000-7121C Roof Jack 15"-26"

Standard roof jack same as above except adjustable from 15"-26". Your price $185.00.
4000-7121C standard Coleman roof jack. 7680B6541 Exterior Roof Jack Extension

Extends crown of roof jack up an extra 18 inches to clear drifting snow or down drafts which may cause pilot outages. For use with 4000 series Coleman roof jacks. Not adjustable. Installation instructions included. Extensions should not be used or extend inside attic spaces. Use only above roofline. Your price $67.00.

View instruction sheet.
7680B6541 exterior roof jack extension.
4000-7141C Roof Jack 23"-44"

Standard roof jack same as above except adjustable from 23"-44". Oversize shipping applies. Your price $215.00.
4000-7141C standard Coleman roof jack. 7900A6111 Interior Roof Jack Extension 11"

Interior roof jack extension lengthens roof jack connection to furnace by 11". Extension not adjustable but roof jack is. Extensions should not be used or extend inside attic spaces. Use only between furnace and ceiling line. Your price $67.00.

7900A6111 interior roof jack extension.
4000-7151C Roof Jack 30"-56"

Standard roof jack same as above except adjustable from 30"-56". Oversize shipping applies. Your price $226.00.
4000-7151C standard Coleman roof jack. 7900A6171 Interior Roof Jack Extension 17"

Interior roof jack extension lengthens roof jack connection to furnace by 17". Extension not adjustable but roof jack is. Extensions should not be used or extend inside attic spaces. Use only between furnace and ceiling line. Your price $73.00.

7900A6171 interior roof jack extension.
4000-6941C Crown Assembly

Crown assembly for a standard Coleman roof jack. Outside pipe is 8-1/2" which fits over an 8-1/4" pipe. Inside pipe is 5-1/2" which fits over a 5-1/4" pipe. Attaches with three screws (not included). Be sure your old crown is removable. If not, order complete roof jack. Your price $137.78.
View instruction sheet.
Crown Assembly 4000-5441C Crown Cap

Roof cap for top of crown assembly. Pipe size is 5-3/8" which fits over a 5" pipe. Connects with two screws (not included). Your price $46.20.

Crown Cap
Duct Connector

Connects a downflow furnace to the ductwork underneath it. To specify the correct size, measure from the top of the floor to the top of the duct. Secure to floor and bend fingers inside duct opening. Opening size is 12" x 14". Total size is 18" x 18". Depths available are 2", 4.5", 6.5", 7.5", 8.5", 10.25", and 12". Price starts at $54.00.
Duct Connector 7660-2841 Ceiling Ring

Metal ceiling ring fits around furnace pipe to seal gap where furnace pipe protrudes through the ceiling. Also used to meet fire code. Two pieces for easy installation. Fits around an 8" pipe. Screws not included. Your price $12.00.

Ceiling ring
7900-6771 Damper

Damper is located underneath furnace and fits inside above duct connector. Opens automatically when furnace blower comes on. Shuts when furnace blower shuts off. When the furnace is not used, the damper keeps air from ductwork from coming back up inside the furnace. Damper is often used when separate a/c units don't require use of the furnace blower. A 12" x 12" minimum opening in duct needed to use damper. Total size is 17.5" x 18". Your price $79.00.
Coleman Damper

We ship all our own parts. If you ever have a problem, you deal
directly with us, not a third-party drop-shipper.


#5050 5" Insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. Also used in attic venting systems. 25' long. Was $39.00, Your price $15.00.
Insulated cross-over flex duct #5052 6" insulated cross-over flex duct

Used to connect ductwork in homes. 25' long. Your price $33.32.

Insulated cross-over flex duct
#5054 8" Insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. 25' long. Your price $39.42.
Insulated cross-over flex duct #5056 10" insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. 25' long. Your price $59.72.

Insulated cross-over flex duct
#5058 12" Insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. 25' long. Your price $70.74.
Insulated cross-over flex duct #5060 14" insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. 25' long. Your price $79.62.

Insulated cross-over flex duct
#5062 16" Insulated cross-over flex duct

Used underneath home to connect ductwork in multi-section homes. 25' long. Oversize shipping applies. Your price $95.00.
Insulated cross-over flex duct.

We sincerely hope that the information and service we've provided
will earn your business. Thank you for your patronage.


Click Here to request a quote on a Coleman part you don't see listed.
Please include part number (if known) and model number of furnace.
You will receive a response within hours.
Please note that some older part numbers do change, which we can help you with.


Need help finding the right part, please e-mail us.
Need help troubleshooting your furnace, please click here.

Click here to troubleshoot your Blend Air II system.

Questions?

E-mail us anytime!

Top of Catalog
Ordering Instructions
Add your product to our online catalog





Trouble finding what you are looking for?  Try a Search Below
Google
 
Web mobilehomerepair.com