Hi everyone, i'm new here and desparate for help. I haven't been able to find the parts for my Miller cmf80 since before Xmas. I got the new motor, found the fan housing wouldn't fit. Got the new fan housing and fan, they are too small plus the housing has a rectangular hole that goes into the furnace and the furnace has a round hole, Do i have to replace the whole assembly that bolts on to the furnace?
Thanks, Lynda
burner motor on CMF80 propane
Hi Lynda,
What is complete furnace model number ? Look for some more letters with a dash between them.
Are you just needing a burner motor ?
Thanks,
Robert
What is complete furnace model number ? Look for some more letters with a dash between them.
Are you just needing a burner motor ?
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Hi Lynda,
Could that possibly be CMF80-PG ?
If not, are there any numbers or data info on the burner motor or burner assembly ?
There are several types, so need to get correct one.
Thanks,
Robert
Could that possibly be CMF80-PG ?
If not, are there any numbers or data info on the burner motor or burner assembly ?
There are several types, so need to get correct one.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Hi Robert,
it does have AG not PG. I will have to look at the other numbers when i get home. I normally e-mail form work because i have dial up at home. I gave all the numbers i could find to the mobile home supply guy near here and the part he came up with is a replacement for the discontinued part. It is similar but has a couple very different features. The hole to put oil in for the flywheel will be on the bottom if the motor is installed like the old one. The wires for the switch are in a different spot as well. I think the furnace was originally gas and was converted to propane.
Thanks, Lynda
it does have AG not PG. I will have to look at the other numbers when i get home. I normally e-mail form work because i have dial up at home. I gave all the numbers i could find to the mobile home supply guy near here and the part he came up with is a replacement for the discontinued part. It is similar but has a couple very different features. The hole to put oil in for the flywheel will be on the bottom if the motor is installed like the old one. The wires for the switch are in a different spot as well. I think the furnace was originally gas and was converted to propane.
Thanks, Lynda
Lynda
-
- Similar Topics
- Replies
- Views
- Last post
-
-
intertherm standing pilot propane burner Heat Rise of 38°F spread.
by justplumducky » Fri Aug 25, 2017 10:06 am » in Nordyne Service & Repair - 0 Replies
- 53627 Views
-
Last post by justplumducky
Fri Aug 25, 2017 10:06 am
-
-
-
Where to place propane wall heaters?
by nestsman » Wed Jun 28, 2017 2:18 pm » in All Other HVAC Questions - 5 Replies
- 56784 Views
-
Last post by suzy_dickson
Fri Jul 05, 2019 1:24 am
-
-
-
Propane wall heater flickers badly
by nestsman » Tue Nov 28, 2017 1:23 pm » in Service & Repair of Other Brands - 2 Replies
- 33028 Views
-
Last post by suzy_dickson
Fri Jul 05, 2019 12:54 am
-
-
- 0 Replies
- 42549 Views
-
Last post by MobileMike
Sat Oct 26, 2019 12:57 am
-
-
Intertherm standing pilot LPG burner 77 BTU IN gas valve mounting plate gets hot ( not warm).
by justplumducky » Sat Sep 09, 2017 3:34 am » in Nordyne Service & Repair - 1 Replies
- 73162 Views
-
Last post by Maxwell.lipphardt
Thu Nov 22, 2018 10:15 am
-