I had someone come out a check my furnace today due to it not working. They said the Gas valve was bad and it is no longer made. The told me I need a whole new furnace due to lack of finding a valve. Do you carry the valve needed for this make and model.
Rachel
Since it has to due with the gas valve. My guess is I cant do it myself...right? Money is super tight right now and I am just trying to keep my family afloat. Can you give me a rough estimate on how much it would cost to have someone come in and do it for me?
Intertherm MGH055ABWN06
Hi Marie,
Gas Valve # 624583 @ $295.00 + $8.00 shipping can be seen and ordered through
PayPal from left side of this page :
http://www.mobilehomerepair.com/NordyneGas.html
Yes, you would need an hvac tech or someone experienced in this type replacement.
Costs can vary widely from area to area due to cost of living there, overhead at contractor, ease of replacement, etc... .
I would say labor would be anywhere from $100 to $200, so all together, this is a pricey repair.
Be sure the gas valve is bad though, what did they do to determine it was bad ?
Check for 24vac at gas valve terminals with a call for heat.
IF you have 24 to 28vac at that time, then check for correct input and manifold gas pressures.
Gas valve is bad only when the 24vac is there and correct input pressure is there, but the manifold pressure is not there at all or is not correct.
Hope this helps some.
Thanks,
Robert
Gas Valve # 624583 @ $295.00 + $8.00 shipping can be seen and ordered through
PayPal from left side of this page :
http://www.mobilehomerepair.com/NordyneGas.html
Yes, you would need an hvac tech or someone experienced in this type replacement.
Costs can vary widely from area to area due to cost of living there, overhead at contractor, ease of replacement, etc... .
I would say labor would be anywhere from $100 to $200, so all together, this is a pricey repair.
Be sure the gas valve is bad though, what did they do to determine it was bad ?
Check for 24vac at gas valve terminals with a call for heat.
IF you have 24 to 28vac at that time, then check for correct input and manifold gas pressures.
Gas valve is bad only when the 24vac is there and correct input pressure is there, but the manifold pressure is not there at all or is not correct.
Hope this helps some.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Hi Rachel,
Sorry about name mix-up, didn't see your name in middle of post. Just went by email addy of Marie.
Thanks,
Robert
www.mobilehomerepair.com
Sorry about name mix-up, didn't see your name in middle of post. Just went by email addy of Marie.
Thanks,
Robert
www.mobilehomerepair.com
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
intertherm standing pilot propane burner Heat Rise of 38°F spread.
by justplumducky » Fri Aug 25, 2017 10:06 am » in Nordyne Service & Repair - 0 Replies
- 51127 Views
-
Last post by justplumducky
Fri Aug 25, 2017 10:06 am
-
-
-
Intertherm standing pilot LPG burner 77 BTU IN gas valve mounting plate gets hot ( not warm).
by justplumducky » Sat Sep 09, 2017 3:34 am » in Nordyne Service & Repair - 1 Replies
- 70331 Views
-
Last post by Maxwell.lipphardt
Thu Nov 22, 2018 10:15 am
-
-
-
Intertherm outdoor a/c unit, blower not turning off. Model unknown rating plate is faded out.
by tkrueger » Sat May 05, 2018 8:57 pm » in Nordyne Service & Repair - 0 Replies
- 110987 Views
-
Last post by tkrueger
Sat May 05, 2018 8:57 pm
-
-
- 0 Replies
- 74998 Views
-
Last post by newguy47
Thu Aug 16, 2018 8:21 pm
-
-
heater blower intertherm feh-015ha-03
by newguy47 » Wed Oct 24, 2018 8:04 am » in Nordyne Service & Repair - 0 Replies
- 81255 Views
-
Last post by newguy47
Wed Oct 24, 2018 8:04 am
-