I was at a home show recently and was told that I could instale true hard wood flooring in my double wide without any trouble. They told me that they instale it in a lot of mobile homes. I thought laminant flooring was what needed to be used because of the shifting of the house.
I also am in the process of having grab bar installed in my bathroom and have a question. I am getting a 18" vertical bar along side the entrance to the tub/shower. I was told that they could nail into the 2x3 stud and that would be strong enough to hold. I am leary about this because I am a large woman and I need this grab bar to hold if I start to fall again. What is the best way to instale this bar preferably without tearing the wall apart.
true hard wood flooring vs laminate
Moderators: Greg, Mark, mhrAJ333, JD
Personally, I rarely see hardwood flooring in a mobile home. If I were to consider hardwood flooring, I would look at the engineered hardwood flooring. This type of flooring is made like a plywood, with the finish layer being the wood floor you see. Having the woodgrain of the layers going in different directions, makes this type of wood flooring more stable and forgiving of flex.
A good connection to a 2x3 would probably be your best bet without opening a wall. It would all depend on the connection. The 2x3 is strong enough, but a screw glancing off the side of a stud, maybe splitting the wood would not be very trustworthy. You also have to be lucky enough to have a stud where you want it. These safety bars usually fasten to the wall with 3 screws on each end. It can be very tricky trying to get all 3 screws into one 2x as the bracket has screws about 1.5" to 2" apart. You would want 2 screws dead center on the 2x, and the third going in at an angle, screwing into the side of the 2x. I usually use a wall anchor for the third screw. I will not install a safety bar in a mobile home wall with only wall anchors.
Hope this helps.
JD
A good connection to a 2x3 would probably be your best bet without opening a wall. It would all depend on the connection. The 2x3 is strong enough, but a screw glancing off the side of a stud, maybe splitting the wood would not be very trustworthy. You also have to be lucky enough to have a stud where you want it. These safety bars usually fasten to the wall with 3 screws on each end. It can be very tricky trying to get all 3 screws into one 2x as the bracket has screws about 1.5" to 2" apart. You would want 2 screws dead center on the 2x, and the third going in at an angle, screwing into the side of the 2x. I usually use a wall anchor for the third screw. I will not install a safety bar in a mobile home wall with only wall anchors.
Hope this helps.
JD
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Very good point Greg. Also makes me think that a person might have to glue and nail the hardwood down because of the particle board floors.
Personally, I would replace the particle board sub-floor with 3/4" tongue & groove plywood before I would install any premium floor product. I repaired a PB pipe/floor damage that had that epoxy-pebble flooring in. The particle board didn't stand a chance. They say to steam clean stains and for deep cleaning. I would think that would soften the particle board too. Really nice looking floor though!
JD
Personally, I would replace the particle board sub-floor with 3/4" tongue & groove plywood before I would install any premium floor product. I repaired a PB pipe/floor damage that had that epoxy-pebble flooring in. The particle board didn't stand a chance. They say to steam clean stains and for deep cleaning. I would think that would soften the particle board too. Really nice looking floor though!
JD
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
- Jim from Canada
- Posts: 551
- Joined: Mon Mar 05, 2007 10:39 am
one thing about laminate flooring. It will wear much better than hardwood if you have pets. Although I must say, our dog is not too keen on the lack of traction, plenty of rubber backed mats for her though.
My first Laminate floor had the following instructions for cleaning. " use mild soap & water to wash, stubborn stains may require acetone" (Nail polish remover) . If that will not stand up to a power chair, not much will. Greg
"If I can't fix it, I can screw it up so bad no one else can either."
As to the bathroom grab bars, I installed one on either side of the shower just at the edge but not in the shower. Mine are 1 1/2 diameter and 24 inch high.
Since I rebuilt the wall from scratch I doubled the 2x4 studs at the level where the grab bars would go, therefore assuring that the three 3" screws would have a good bite and BOY did they bite. I always try to Over-build" things just in case.
Since I rebuilt the wall from scratch I doubled the 2x4 studs at the level where the grab bars would go, therefore assuring that the three 3" screws would have a good bite and BOY did they bite. I always try to Over-build" things just in case.
1987 Craftsman Double Wide 42x28,w/attached 28x12 foot enclosed porch/ re-shingled 2 yrs ago. Original exterior vinyl w/no sheathing.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3 Replies
- 56102 Views
-
Last post by Mark440
Sat Apr 03, 2021 6:50 pm
-
-
'73 Viking Doublewide - Odd Ceiling Panels Hard to Remove
by 73Viking » Mon Dec 03, 2018 1:05 am » in Mobile Home Repair - 4 Replies
- 30571 Views
-
Last post by Greg
Mon Dec 10, 2018 5:34 pm
-
-
-
Hanging a non hard wired light, how heavy?
by Carlo.clausen » Mon Jun 15, 2020 9:40 pm » in Mobile Home Repair - 1 Replies
- 12110 Views
-
Last post by Greg
Tue Jun 16, 2020 4:14 pm
-
-
- 1 Replies
- 10216 Views
-
Last post by Greg
Mon Aug 21, 2017 7:03 pm
-
-
Silicone calking for concrete, wood and metal?
by mdnagel » Thu Aug 22, 2019 11:24 pm » in Mobile Home Repair - 4 Replies
- 19739 Views
-
Last post by Lancer21
Sat Aug 31, 2019 2:59 am
-