Vent pipe roof leak
Moderators: Greg, Mark, mhrAJ333, JD
Most homes are plumbed with 1 1/2" ABS pipe for venting. I have seen a few that were 2", but we are talking 1% or less of the 1000 or so roofs I have looked at over the years.
If you need to, you can enlarge the hole so you have 1/2" clearance around the pipe and add a couple and short piece of pipe. On metal roofs I like for the pipe to be a little long and then cut it off after I glue it in, I will cut it 1 1/2" above the roof line and install a metal vent cap.
If you need to, you can enlarge the hole so you have 1/2" clearance around the pipe and add a couple and short piece of pipe. On metal roofs I like for the pipe to be a little long and then cut it off after I glue it in, I will cut it 1 1/2" above the roof line and install a metal vent cap.
You do not have the required permissions to view the files attached to this post.
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
I put a big bead of roof caulking under the screw flange and install it with #10 hex head screws. The sealant will ooze out all around the vent. I use that sealant and little more from the caulk gun to seal the top side. Make sure the roof surface, the bottom and top of that vent cap's flange are lacquer thinner clean. New galvanized vents will have a film of production oil on them. This must be cleaned off or the sealants won't last very long. If the roof metal around the pipe is really goobered up with old sealants, you might consider getting a bigger vent cap to be able to screw into better metal.
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
-
- Posts: 4
- Joined: Sat Oct 30, 2010 9:52 am
Roof venting can be hard, but the suggestion above is right on the money. You want to make sure this get sealed properly, and we all know how hard it is to work with something that was done improperly to start. Cut out the clearance and add the stub. I have never seen 2" piping, but it could depend on the code where you live.
If your plumbing vent pipe slid down because a strap came loose, you might want to check the horizontal 3" ABS under the floor that it is connected to. This pipe should be strapped to the framing every 4'. The plumbing vent should not be able to slide down in the first place. That horizontal 3" pipe under the home should be straight and have a 1/4" per ft drop. If your vent pipe was able to drop inches down into the hole, you could very well have some plumbing drain problems in the near future.
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 94504 Views
-
Last post by Raktus84
Fri Aug 21, 2020 11:38 am
-
- 2 Replies
- 15761 Views
-
Last post by cjb2145b
Sun May 03, 2020 10:11 am
-
- 1 Replies
- 3207 Views
-
Last post by Greg
Sun Oct 14, 2018 8:41 am
-
-
Doublewide - Vent or Leave roof Non-vented?
by 73Viking » Fri Jun 14, 2019 7:00 pm » in Mobile Home Repair - 2 Replies
- 11106 Views
-
Last post by 73Viking
Sat Jul 13, 2019 12:21 pm
-
-
- 1 Replies
- 29121 Views
-
Last post by Greg
Sun Mar 11, 2018 5:47 pm