Where to start...Ok someone came to fix the air earlier this year and installed a relay, a/c works great but no heat to start with. After investigating I found the sequencer was brittle and fell into three pieces then in the process of changing it the wires just fell out of the fan switch(ifs). I purchased a new fan switch and installed it today Now my 1st stage of the strips will come on but no fan so the limit kicks out. I manually turned the fan from the t-stat to on and both 1st and 2nd stage heat work fine now, but the fan has to run at all times so I investigated some more with the fan switch I put on. When the fan switch is in auto as I said before, 1st stage, no fan, then limits out, but when switched to on, fan dont run but the 1st stage strip comes on??? This fella who came before me has something wrong and I have a very limited schematic to go by...Can you get your hands on a in detail schematic of the way this units originally wired and perhaps offer any advice? I have one limit and one 2 stage sequencer in the panel that are original and 1 after market relay put in by the fella before me, I believe the aftermarket relay is whats wrong. Are there suppose to be any other relays or sequencers besides the 1 sequencer and one relay I see that are factory? If you have one that you can maybe take a picture of the panel and have a schematic handy I believe I can figure it out.
Thanks a bunch...
The clean up guy...
And just to let you know you have been more then helpful in the past I greatly appreciate you...
e2eb-012h Fan works great but wont come on with strips...
Hi ,
Glad to help, you're very welcome. Go here and follow steps to order wiring & parts diagrams.
http://www.mobilehomerepair.com/wireandparts.html
Got to run over to other home we bought and finish furnace repair.
When I return, I'll check back again.
Sequencer :
http://www.mobilehomerepair.com/media/i ... 621679.jpg
Blower Relay:
http://www.mobilehomerepair.com/media/i ... 621867.jpg
Heating Element:
http://www.mobilehomerepair.com/media/i ... 902824.jpg
The sequencer controls the heating elements and the blower motor for heat mode.
The blower relay controls the blower motor for a/c mode.
Thanks,
Robert
Glad to help, you're very welcome. Go here and follow steps to order wiring & parts diagrams.
http://www.mobilehomerepair.com/wireandparts.html
Got to run over to other home we bought and finish furnace repair.
When I return, I'll check back again.
Sequencer :
http://www.mobilehomerepair.com/media/i ... 621679.jpg
Blower Relay:
http://www.mobilehomerepair.com/media/i ... 621867.jpg
Heating Element:
http://www.mobilehomerepair.com/media/i ... 902824.jpg
The sequencer controls the heating elements and the blower motor for heat mode.
The blower relay controls the blower motor for a/c mode.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Got it bud ....Thanks all I needed was the schematic...The fella before me had wires missing and miswired like crazy but 15 minutes later were running fine...
Yep, that would make it rather difficult w/o the wiring diagram.
You're very welcome, glad you're warm now and all is good to go.
Thanks for allowing us to assist you.
Take care and best wishes,
Robert
You're very welcome, glad you're warm now and all is good to go.
Thanks for allowing us to assist you.
Take care and best wishes,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Heat strips are on, but not the fan.
by Forestbrook » Sat Dec 08, 2018 6:09 pm » in Coleman Service & Repair - 0 Replies
- 41406 Views
-
Last post by Forestbrook
Sat Dec 08, 2018 6:09 pm
-
-
- 0 Replies
- 107028 Views
-
Last post by Colbey8466
Mon Feb 10, 2020 3:44 am
-
-
Belly wrap repair with furring strips
by mdnagel » Mon Sep 16, 2019 11:34 am » in Mobile Home Repair - 1 Replies
- 10945 Views
-
Last post by Greg
Mon Sep 16, 2019 6:47 pm
-
-
-
Removing the seem strips on the walls
by J_SEPH0729 » Mon Sep 30, 2019 9:01 am » in Mobile Home Repair - 2 Replies
- 10436 Views
-
Last post by J_SEPH0729
Tue Oct 01, 2019 8:15 am
-
-
-
HVAC duct redirect - IT WORKS !
by Mark440 » Mon Jul 01, 2019 11:30 am » in All Other HVAC Questions - 0 Replies
- 30203 Views
-
Last post by Mark440
Mon Jul 01, 2019 11:30 am
-