My nordyne intertherm furnace model E2EB-015HB caught on fire. It was working fine on a/c with no problems.
We turned on the heat for the first time and it sounded like it was struggling, it was blowing heat but not very hard. It smelled really bad, not that first time use smell, but like a hot electrical smell. I switched the fan to "on" position and it worked fine, had heat, blew full speed and no smell. I turned it off after 5 minutes because I was afraid of it.
I turned it on later (in auto setting) with the bottom cover off to let my husband hear it..had the same smell. After 30 seconds or so it had a loud pop, sparks flew and the fire started in the blower motor. We had to use the extinguisher to put it out. It didn't damage anything around the motor (no burnt wires, didn't even burn the dust off). We put it back on the a/c setting and tried it, wouldn't even try to come on.
I had a service tech come out and he said it needs a new motor. He said he would call me with a price but when he called back he said we can't just replace the motor and need to replace the whole furnace, $1,100.
Should I get a second opinion or just let him replace it?
Should I get a second opinion
Intertherm e2eb-015hb fire
You can replace every part in that furnace for less than $1100. IF a motor is all it needs, then that is all I would replace.
We have any part needed and can help with any replacement info needed.
Thanks,
Robert
We have any part needed and can help with any replacement info needed.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Thanks for your reply. I'm positive that it needs the blower motor since it caught fire. What I'm not sure of is if something else could have been wrong to make it do that. Could the motor work fine in a/c mode and not on heat? It was fine when the a/c was on. Just had the weird smell on heat setting and then only when it was on auto. Did fine in the fan on setting.
I know I need the motor, but is there a way to know if I need something else too prior to replacing the motor?
I know I need the motor, but is there a way to know if I need something else too prior to replacing the motor?
You'll need a new run capacitor. Look at all wires, connections, etc... . May need a new sequencer or fan relay.
Thanks,
Robert
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Question about burned wiring on e2eb-015ha
by thomasclay » Thu Sep 14, 2017 5:37 pm » in Nordyne Service & Repair - 0 Replies
- 59469 Views
-
Last post by thomasclay
Thu Sep 14, 2017 5:37 pm
-
-
-
Replace relay for Emergency. Heat in E2EB-15HB
by istvv4848 » Tue Oct 23, 2018 10:49 am » in Nordyne Service & Repair - 0 Replies
- 38930 Views
-
Last post by istvv4848
Tue Oct 23, 2018 10:49 am
-
-
-
intertherm standing pilot propane burner Heat Rise of 38°F spread.
by justplumducky » Fri Aug 25, 2017 10:06 am » in Nordyne Service & Repair - 0 Replies
- 47323 Views
-
Last post by justplumducky
Fri Aug 25, 2017 10:06 am
-
-
-
Intertherm standing pilot LPG burner 77 BTU IN gas valve mounting plate gets hot ( not warm).
by justplumducky » Sat Sep 09, 2017 3:34 am » in Nordyne Service & Repair - 1 Replies
- 66208 Views
-
Last post by Maxwell.lipphardt
Thu Nov 22, 2018 10:15 am
-
-
-
Intertherm outdoor a/c unit, blower not turning off. Model unknown rating plate is faded out.
by tkrueger » Sat May 05, 2018 8:57 pm » in Nordyne Service & Repair - 0 Replies
- 106301 Views
-
Last post by tkrueger
Sat May 05, 2018 8:57 pm
-