Hi,
The pilot light is not on and it states not to attempt to light manually.
I know there is a manual reset switch (according to the writing on the heater itself) but cannot find it. There is not a switch with a red or any other type of button in the middle, anywhere.
The air conditioner works as does the fan if I turn it on, just nothing from the heater.
I do not have the manual and cannot find one to download on the internet.
Thanks for any help.
MMHA 070ABHR -05 Gas Heater non responsive
Hi,
Manuals can be ordered from here:
http://www.hvacmanuals.com/
If you cannot find yours, call Mark at 605-229-2627 and see if he has one not listed yet.
IF nothing happens when in heat mode, probably an electrical problem with wiring or a component such as the control module.
I offer a $20 troubleshooting fee if you want steps on what/where to test with volt meter. I do this by email one on one.
You do not have a pilot light, your furnace uses a hot surface ignitor for igniting the burner.
Thanks,
Robert
Manuals can be ordered from here:
http://www.hvacmanuals.com/
If you cannot find yours, call Mark at 605-229-2627 and see if he has one not listed yet.
IF nothing happens when in heat mode, probably an electrical problem with wiring or a component such as the control module.
I offer a $20 troubleshooting fee if you want steps on what/where to test with volt meter. I do this by email one on one.
You do not have a pilot light, your furnace uses a hot surface ignitor for igniting the burner.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Thanks for the response.
A search shows no manual at the link you provided so I will call Mark tomorrow.
The instructions on the actual furnace state to push in the manual limit switch reset button if the burner does not function. I know what the reset button is supposed to look like but I still cannot find it.
Once found, if the furnace still doesn't work I will definitely need some troubleshooting guidance.
Thanks again
A search shows no manual at the link you provided so I will call Mark tomorrow.
The instructions on the actual furnace state to push in the manual limit switch reset button if the burner does not function. I know what the reset button is supposed to look like but I still cannot find it.
Once found, if the furnace still doesn't work I will definitely need some troubleshooting guidance.
Thanks again
It's usually on the middle shelf area, left side near blower assembly or mounted to side of blower assembly housing.
Mark may or may not have a manual, but call him and see.
Let me know if you need the link to the troubleshooting fee info.
Thanks,
Robert
Mark may or may not have a manual, but call him and see.
Let me know if you need the link to the troubleshooting fee info.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1 Replies
- 36518 Views
-
Last post by Greg
Fri Apr 20, 2018 5:11 pm
-
-
Doublewide - Vent or Leave roof Non-vented?
by 73Viking » Fri Jun 14, 2019 7:00 pm » in Mobile Home Repair - 2 Replies
- 10750 Views
-
Last post by 73Viking
Sat Jul 13, 2019 12:21 pm
-
-
-
Hanging a non hard wired light, how heavy?
by Carlo.clausen » Mon Jun 15, 2020 9:40 pm » in Mobile Home Repair - 1 Replies
- 11957 Views
-
Last post by Greg
Tue Jun 16, 2020 4:14 pm
-
-
-
I am thinking of switching to a gas water heater
by deryk the gypsy » Sat Jul 22, 2017 7:16 am » in Mobile Home Repair - 2 Replies
- 36637 Views
-
Last post by Greg
Sat Jul 22, 2017 12:26 pm
-
-
-
Need to remove a stripped Allen wrench-type plug from the OUT PRESS port on top of gas valve
by justplumducky » Fri Aug 25, 2017 8:21 am » in Nordyne Service & Repair - 1 Replies
- 46643 Views
-
Last post by Maxwell.lipphardt
Mon Feb 04, 2019 6:29 am
-