Hi All,
After flushing and recharging my pressure tank recently, I have had problems with sediment in the cold water lines plugging up fixtures and reduced water pressure. Anyone have any ideas on how to quickly flush all the sediment from the entire cold water system? I have had this problem before during power outages and the pressure tank empties completely...over time the sediment is slowly removed after repeated cleanings of faucet screens. I have thought of using the hot water line at the spigot in the utility room to backflush through the cold water line and out through the outside hose bibb...if I keep all the other fixtures turned off, it should flush most of the sediment outside, or hopelessly clog all the fixtures again. Ideas???
Sediment in water supply lines
Moderators: Greg, Mark, mhrAJ333, JD
I don't think there is a quick way other than removing the screens and flushing the system. You may want to think about a whole house filter system to prevent or reduce the problem. They are simple to install.
Greg
http://www.acehardware.com/product/inde ... 1386643684
Greg
http://www.acehardware.com/product/inde ... 1386643684
"If I can't fix it, I can screw it up so bad no one else can either."
Hi Greg,
Yes, I suppose I'll just have to be patient and let the sediment slowly work its way out. Where is the filter usually placed...before or after pressure tank, main shut-off valve? I'd like to keep the sediment out of the tank as well, however there's not much room to work there before the riser comes through the floor.
Yes, I suppose I'll just have to be patient and let the sediment slowly work its way out. Where is the filter usually placed...before or after pressure tank, main shut-off valve? I'd like to keep the sediment out of the tank as well, however there's not much room to work there before the riser comes through the floor.
You can put the filter anywhere, but to protect the tank you would need to install it before the tank. You could install 2 filters, one before the tank & one after the tank, that way if the first goes into bypass mode the rest of the system would be protected.
Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
- flcruising
- Posts: 606
- Joined: Mon Dec 03, 2007 2:18 pm
- Location: Florida Panhandle
FYI - I tried installing a water filtering system before the pressure tank once and the pump short cycled constantly because of the restriction caused by the filter. If you install before your main pressure tank, you may have to add a smaller pre-pressure tank to dampen the surge when the pump initially turns on. But then again, maybe a lower restriction sediment filter won't cause that issue.
[color=blue]Aaron[/color]
Indeed...in my case, installing a filter seems to be more trouble than it is worth. I managed to flush most of the sediment out through the outside hose bibb just by running the water at full tilt for about 5-10 pump cycles...along with multiple cleanings of all the faucet cartridges and screens, and toilet fill valve. Also drained the water heater just for good measure. I just have to be very careful not to turn on the house main valve BEFORE all the sediment is removed from my pressure tank. A lot of the "sediment" appears to be rust particles probably from the galvanized tee which links the riser to the pressure tank and the main water line.
Cheers, Steve
Cheers, Steve
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2 Replies
- 9274 Views
-
Last post by jben04564
Tue May 07, 2019 3:47 pm
-
-
Bathroom subfloor water damage from toilet supply line
by Bluejayz79 » Mon Jul 23, 2018 7:29 pm » in Mobile Home Repair - 1 Replies
- 28158 Views
-
Last post by Greg
Tue Jul 24, 2018 7:20 pm
-
-
- 5 Replies
- 35580 Views
-
Last post by Joe Freeman
Sun Jul 23, 2017 7:32 am
-
- 2 Replies
- 26932 Views
-
Last post by mdnagel
Tue Jun 04, 2019 6:36 pm
-
- 1 Replies
- 24875 Views
-
Last post by Greg
Fri Oct 25, 2019 7:57 pm