Have a 1993 Southern Energy DW. I have a bank of wall plugs in the kitchen that are dead. Electrician came out and found that the lead wall plug had no power from the panel. He said the breaker had power coming out but no power at the plug. He concluded there must be a break in one of the wires from the panel to the plug and we need to get into the attic to check. Of course, no attic access. Anyone have suggestions on how I can create my own small access? I have a good size walk in closet and might could cut a hole in the ceiling and frame one in but wanted to check here first for suggestions. BTW, these are not GFI protected plugs, they work fine..
Mike
Need attic access for electrical problem
Moderators: Greg, Mark, mhrAJ333, JD
- flcruising
- Posts: 606
- Joined: Mon Dec 03, 2007 2:18 pm
- Location: Florida Panhandle
You will find that 99% of MH's have branch circuits run below the floor joists, not overhead. If you can find an access panel in the belly material underneath a tub or shower on the side of the home you need to work, you may be able to stick your head up there and look down the gap between the joist and the insulation and locate the wiring. Also, if your electrician pulled the cover from the circuit panel to check the branch at its source, then he should have verified which direction the wire exits the panel (up or down). I would double-check this before cutting any access holes in the ceiling. Electrical advise is not allowed to be given on this site, but be aware that even if you do locate the break in the wire, per code, it must remain accessible via a junction box if you repair with wire nuts. My suggestion is abandon that wire and have him run a new continuous feed underneath.
[color=blue]Aaron[/color]
Hi & welcome. Most of the homes here run the wires through the walls about 18" off the floor. If you have aluminum siding it may be an easy way to gain access just by removing the screws and opening up the outside panels. I agree that most have the circuits piggybacked from one outlet to the next, so if you loose it in one the rest past that are dead.
Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
I think it would probably be easier and faster to run a new wire than trying to examine the existing conduit break. I would go through the floor joists, myself.
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
-
- Posts: 34
- Joined: Wed Aug 22, 2012 7:44 pm
There could also be a GFI outlet before that area that has tripped. I have seen bathroom GFIs tied to outlets in areas that you would not expect... worth taking a look. Also if your outlets are "backstabbed" instead of wired to the side terminals, that can also be a cause. I really don't see a break in the line being the most likely problem.
-
- Posts: 383
- Joined: Mon Oct 25, 2010 9:53 pm
- Location: Steuben County, NY
I have one GFI outlet in the master bath which controls the outside outlet, the one under the home for the heat tape, and both bathrooms. strangely enough, no GFI protection in the kitchen.
Before tearing things apart, check the connections that join the circuits together from one half of the home to the other. The connectors they use are pretty crappy. I usually cut those away and wire things up direct inside a junction that I install. Those connections are located at the marriage line underneath the home at the front and/or back usually within 5' of the end of the unit.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 7 Replies
- 38216 Views
-
Last post by mdnagel
Wed Jun 05, 2019 6:43 pm
-
- 0 Replies
- 115112 Views
-
Last post by Addy1today
Wed Dec 01, 2021 9:20 pm
-
- 2 Replies
- 82637 Views
-
Last post by Greg
Wed Aug 30, 2017 5:05 pm
-
-
Disable Blend Air ll Attic fan
by 777stickman » Fri Nov 17, 2017 5:05 pm » in Coleman Service & Repair - 0 Replies
- 44304 Views
-
Last post by 777stickman
Fri Nov 17, 2017 5:05 pm
-
-
-
plastic vapor barrier no attic vents
by timemeddler » Fri Feb 07, 2020 6:56 pm » in Mobile Home Repair - 1 Replies
- 30700 Views
-
Last post by Greg
Sat Feb 08, 2020 9:37 am
-